CivilBlog.Org

Oxygen Permeability Test of Concrete — IS 516 (Part 2/Sec 3): 2022

Suryakanta — Mon, 31 Aug 2026 09:33:08 +0000

Oxygen Permeability Test of Concrete The oxygen permeability test is a durability test used to assess the permeability of hardened concrete to gas. It provides an Oxygen Permeability Index (OPI), which is particularly useful for evaluating the quality and durability of the concrete cover. Reference: IS 516 (Part 2/Sec 3): 2022, Hardened Concrete — Methods ... Read more

The post Oxygen Permeability Test of Concrete — IS 516 (Part 2/Sec 3): 2022 appeared first on CivilBlog.Org.

ASTM D6760 Crosshole Logging Test of Piles – A Quick Guide

Suryakanta — Sat, 29 Aug 2026 09:29:37 +0000

Crosshole Logging Test of Piles Crosshole logging (CSL), designated Ultrasonic Crosshole Testing in ASTM D6760, is a non-destructive method for assessing the homogeneity and integrity of concrete in bored piles, drilled shafts and other deep foundation elements. It detects anomalous zones by measuring ultrasonic pulse transmission between access ducts installed in the pile. Principle A ... Read more

The post ASTM D6760 Crosshole Logging Test of Piles – A Quick Guide appeared first on CivilBlog.Org.

Setting Time Test of Concrete as per ASTM C403

Suryakanta — Fri, 28 Aug 2026 08:26:02 +0000

Setting Time Test of Concrete The setting of concrete is a gradual process, and therefore its initial and final setting times must be defined by specified measurable criteria. The penetration resistance method determines these times from the resistance offered by the mortar fraction sieved from fresh concrete. Reference ASTM C403/C403M – Time of Setting of ... Read more

The post Setting Time Test of Concrete as per ASTM C403 appeared first on CivilBlog.Org.

Initial Surface Absorption Test of Concrete – [IS 516 (Part 2/Sec 2): 2020]

Suryakanta — Thu, 27 Aug 2026 10:52:07 +0000

Concrete durability is often governed not only by its compressive strength but also by the quality of its surface zone. The outer layer of concrete is the first line of defence against rainwater, moisture and other environmental actions. A concrete surface that absorbs water rapidly may indicate poor finishing, inadequate curing, a porous surface layer ... Read more

The post Initial Surface Absorption Test of Concrete – [IS 516 (Part 2/Sec 2): 2020] appeared first on CivilBlog.Org.

Construction of Concrete Pavements – A Quick Guide

Suryakanta — Wed, 26 Aug 2026 05:17:42 +0000

Concrete Pavement Construction Process The construction of concrete pavement involves sequential construction of subgrade, sub-base/ base and the concrete slab. These are discussed in the following. Subgrade preparation Subgrade preparation involves cleaning, earthwork (excavation or filling of soil, replacement of weak soil, soil stabilization etc.) and compaction. Where the concrete layer is laid directly over the subgrade, the subgrade ... Read more

The post Construction of Concrete Pavements – A Quick Guide appeared first on CivilBlog.Org.

ASTM D5882 Pile Integrity Testing (PIT): A Quick Guide

Suryakanta — Mon, 24 Aug 2026 07:11:35 +0000

Pile Integrity Testing (PIT), also known as low-strain impact integrity testing, is a non-destructive method used to evaluate the continuity, consistency and approximate physical dimensions of deep foundation elements. The test is applicable to driven concrete piles, cast-in-place piles, drilled shafts, augered piles and other deep foundation members that can respond to a low-strain impact. ... Read more

The post ASTM D5882 Pile Integrity Testing (PIT): A Quick Guide appeared first on CivilBlog.Org.

High Density Concrete: Materials, Mix Design, Production and Applications

Suryakanta — Fri, 21 Aug 2026 11:33:27 +0000

Concrete is normally selected for its strength, durability and versatility. However, some applications require another important property: high mass within a limited volume. This is where high density concrete, also known as heavyweight concrete, becomes useful. By replacing conventional aggregates with heavier natural or manufactured materials, concrete with a significantly higher density can be produced. ... Read more

The post High Density Concrete: Materials, Mix Design, Production and Applications appeared first on CivilBlog.Org.

ASTM C39/C39M – Compressive Strength Test of Cylindrical Specimens – A Quick Guide

Suryakanta — Fri, 21 Aug 2026 05:41:24 +0000

The compressive strength test is one of the most important quality-control tests for concrete. ASTM C39/C39M covers the determination of compressive strength of molded concrete cylinders and drilled cores having a density greater than 800 kg/m³. The test involves applying a continuously increasing axial compressive load until failure and calculating the strength from the maximum ... Read more

The post ASTM C39/C39M – Compressive Strength Test of Cylindrical Specimens – A Quick Guide appeared first on CivilBlog.Org.

How to Hire a New Home Construction Contractor: 10 Steps to Choose the Right One

Suryakanta — Thu, 20 Aug 2026 05:27:17 +0000

Building a new home is one of the biggest financial decisions most people will ever make. While the design, location, and finishes are important, the success of the project often depends on one critical decision: choosing the right new home construction contractor. The wrong contractor can lead to delays, cost overruns, poor workmanship, and stressful ... Read more

The post How to Hire a New Home Construction Contractor: 10 Steps to Choose the Right One appeared first on CivilBlog.Org.

IS 16720 Fly Ash Bricks – A Quick Guide

Suryakanta — Tue, 18 Aug 2026 10:14:45 +0000

Fly Ash Bricks – Quality Requirements As per IS 16720 Fly ash bricks, technically referred to in IS 16720:2018 as Pulverized Fuel Ash-Cement Bricks, are masonry units manufactured primarily using pulverized fuel ash (fly ash), cement, aggregates and water. The use of fly ash in bricks provides an effective way of utilizing a thermal power ... Read more

The post IS 16720 Fly Ash Bricks – A Quick Guide appeared first on CivilBlog.Org.