The post Fall Changeover in Albuquerque: Shut Down the Swamp Cooler, Wake Up the Furnace appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The balloons are up, the mornings are crisp, and the first freeze is only a few weeks out. In Albuquerque that means one thing for anyone with an evaporative cooler on the roof: it is changeover season. Shutting the cooler down properly and bringing the furnace back online before the cold arrives protects both systems, keeps your utility bills where they belong, and spares you the scramble for a service call on the first frigid night.
Albuquerque's high desert climate makes fall short and abrupt. Daytime highs can sit in the 70s while overnight lows drop toward freezing, and the first hard freeze typically lands somewhere between mid and late October. A cooler left full of water through a freeze can crack the pump housing, split a supply line, or freeze the float valve. On the other side of the house, a furnace that has sat idle since April may light on the first cold night, or it may not. The window between "still warm enough to run the cooler" and "need the heat tonight" is often just a week or two, so the changeover needs to happen inside that window, not after it.
A swamp cooler shutdown is more than flipping the switch. Done correctly, it includes:
That duct seal is the step homeowners most often skip, and it is the one that costs the most. An open cooler duct is a chimney for heated air. Sealing it is the difference between a furnace that cycles normally and one that runs all night trying to keep up.
The furnace side of the changeover is an inspection first and a startup second. A technician will replace the filter, check the igniter or pilot assembly, and inspect the burners for corrosion and debris. The heat exchanger gets a close look for cracks, which matter because a cracked exchanger can allow combustion gases into the air you breathe. The blower motor, belt, and capacitor are checked for wear, the flue is inspected for obstructions, and the thermostat is tested through a full heating cycle. Carbon monoxide detectors should be tested at the same time, with fresh batteries installed if they are the battery type.
Warning signs that a furnace needs attention before it goes back into service include a burning dust smell that lasts more than a few minutes on first startup, short cycling, a yellow or flickering burner flame instead of steady blue, and any cold rooms that were comfortable last winter. None of these fix themselves, and all of them are easier to address in October than in December.
Scheduling the cooler shutdown and the furnace startup as a single changeover visit saves time and keeps the systems in sync. The same technician who seals the cooler duct confirms the furnace is drawing and delivering air properly through the shared ductwork. Any issue found on one system can be weighed against the other, and you are on the calendar before the first cold snap fills every service slot in the city. For homes with refrigerated air instead of a cooler, the visit becomes a fall heating tune-up with the condenser prepared for the off season.
A changeover is a small job on a mild October afternoon and a much larger one on a freezing November night. Get on the schedule now, and let the balloons be the only thing rising over your house this month.
Academy Plumbing, Heating, Air Conditioning and Electric
3271 Candelaria Rd NE
Albuquerque, NM 87107
(505) 293-4949
The post Fall Changeover in Albuquerque: Shut Down the Swamp Cooler, Wake Up the Furnace appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post Labor Day at Academy Plumbing: Celebrating the People Who Keep Albuquerque Running appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>Bill Collins started working at Academy Plumbing in 1989 [CORRECTION] as a helper, digging ditches and carrying pipe for the men who knew the trade. Over the years that followed he earned his licenses on the job, becoming a master electrician and an HVAC specialist while the company grew with him. When founder Jules F. Appleman built Academy in 1971, he set a standard for honest work and technical skill. Bill spent more than four decades living up to it, and in 2025 he took full ownership of the company he had given his working life to. He made one promise when he did: to keep this place open and make sure these folks have a good job for as long as we could. That is a promise from a tradesman to other tradespeople, made by someone who remembers exactly what it feels like to be the newest helper on the crew. With Derek, his son working alongside him since 2007, Bill leads the way he was led, by showing up, doing the work, and standing behind it.
Many of our employees have been with Academy for ten, twenty, and thirty years. In a trade where turnover is the norm, that kind of tenure does not happen by accident. It happens because people are treated like family, because their skills are respected, and because the work they do is meaningful. Every one of them has spent time in a crawl space in January, on a rooftop in July, and in a stranger’s flooded kitchen at an hour when most people are asleep. They carry licenses that took years to earn and knowledge that cannot be learned from a manual. When a customer tells us the technician was respectful, explained the problem clearly, and fixed it right the first time, that is the person we are celebrating this weekend.
There is a reason plumbers, HVAC technicians, and electricians are classified as essential workers. Water, heat, cooling, and power are not conveniences. A burst supply line can put an inch of water into your home in minutes. A failed air conditioner during a 99 degree August afternoon is a health concern for an elderly resident. A sewer backup is a sanitation emergency no matter what day it is. Our team understands this, which is why Academy Plumbing has always kept someone on call, including on Labor Day. While most of Albuquerque is at a barbecue or on the road, one of our people has a phone within reach and a truck ready to roll. They chose a trade that serves people when people need it most, and they honor that choice even during our own holiday.
On call is not a figure of speech. It means a technician who has planned their holiday around the possibility of leaving it. It means a fully stocked truck parked in the driveway rather than the shop. It means being ready to diagnose a call, replace a failed water heater, clear a main line, or restore power to a panel with the same care they would bring on a Tuesday morning. We do not take that lightly, and we do not want our customers to either. When you call us on a holiday and someone answers, that person gave up part of their day for you.
Labor Day is a good time for the rest of us to notice. If a tradesperson has ever shown up to your home on a weekend, a holiday, or in the middle of the night, a kind word goes a long way. A review that names the technician goes further, because it tells them their work was seen. For our part, we will keep doing what Academy has done since 1971: pay people fairly, keep them working, respect their craft, and stand behind their work with a 100 percent satisfaction guarantee.
To every plumber, technician, electrician, dispatcher, and office team member at Academy Plumbing, Heating, Air Conditioning and Electric: thank you. Enjoy the day. And if your phone rings, we know you will answer it. To our customers, have a safe Labor Day weekend, and if something in your home fails, you know who to call.
Academy Plumbing, Heating, Air Conditioning and Electric, Inc.
3271 Candelaria Rd NE
Albuquerque, NM 87107
(505) 293-4949
The post Labor Day at Academy Plumbing: Celebrating the People Who Keep Albuquerque Running appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post AC Is in Our Name: Why Albuquerque Is Still Talking About Air Conditioning in September appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>Albuquerque normally cools off quickly once Labor Day passes. The average high drops from the upper 80s in the first week of September to the upper 70s by the end of the month, and most homeowners shut down their cooling for the year somewhere in between. This year the forecast is not cooperating. Extended heat into September means air conditioners and evaporative coolers are being asked for an extra three or four weeks of work on top of a summer that already ran hotter and longer than usual. That is not a small ask. In our experience, the last stretch of a long cooling season is when marginal equipment finally gives out.
Every hour of runtime adds wear, but late season hours are harder on equipment than early season hours. Capacitors that were slightly out of tolerance in July have drifted further by now. Contactors have accumulated thousands more start cycles. Condenser coils have collected a full summer of dust, cottonwood, and monsoon grit that raises head pressure and forces the compressor to work against itself. Refrigerant charge that was marginal in June has had all summer to leak down. None of these problems announce themselves loudly. The system just runs a little longer each afternoon, cools a little less, and costs a little more, right up until the day it stops.
If any of the following describe your system, this week is the time to have it looked at rather than the week after it quits:
Each of these points to a specific, diagnosable fault. Each of them also gets more expensive the longer it runs.
Academy Plumbing, Heating, Air Conditioning and Electric has carried all four trades in its name for a reason. Air conditioning is not something we added when it became convenient. Our technicians are trained on refrigerated systems and evaporative coolers alike, and because we also carry licensed electricians, the electrical faults that cause most late season AC failures are diagnosed by people who understand both sides of the problem. When a cooling season runs long, that depth matters. You are not waiting on a subcontractor or being told the season is over and to call back in spring.
The practical argument for a September service call is that it does two jobs at once. A technician who tests capacitor values, checks amperage draw, verifies refrigerant pressures, and clears the condensate drain is keeping your system alive through the remaining heat. That same visit sets you up for the fall changeover. Evaporative coolers can be drained, cleaned, and winterized on the same trip once the weather finally turns. Refrigerated systems can have the furnace side inspected while the technician is already on site. Handling it now, while the heat is still here, means you are not competing for a service slot during the first cold snap in October when every furnace in the city gets turned on the same morning.
Our name has always told you what we do. This September, with the heat hanging on longer than it should, it is also telling you who to call. If your cooling system is struggling through this extended season, call Academy Plumbing, Heating, Air Conditioning and Electric to schedule a diagnostic. Every job we do is backed by our 100 percent satisfaction guarantee.
Academy Plumbing, Heating, Air Conditioning and Electric, Inc.
3271 Candelaria Rd NE
Albuquerque, NM 87107
(505) 293-4949
The post AC Is in Our Name: Why Albuquerque Is Still Talking About Air Conditioning in September appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post The Heat Wave Continues: Late Season AC Repairs Albuquerque Homeowners Should Not Ignore appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>Albuquerque is still running triple digits in August, and your air conditioner has now been working nonstop since May. That accumulated runtime is exactly why late summer produces more no cool calls than any other stretch of the year. Parts that were merely weak in June are failing outright now, and the warning signs usually show up days before the system quits.
Air conditioners do not fail randomly. They fail under load, and load is highest when outdoor temperatures sit near 100 degrees for weeks at a time. Every start cycle draws a surge of current through the run capacitor and contactor, and by late summer those components have absorbed thousands of cycles in extreme ambient heat. A capacitor that tested marginally low in spring will often drift out of tolerance entirely by August. When that happens, the compressor or fan motor tries to start, draws locked rotor amperage, and either trips the breaker or overheats.
The most common late season repair is a run capacitor. The symptoms are recognizable once you know them: the outdoor unit hums but the fan does not spin, the system trips the breaker on startup, or the unit runs briefly and shuts down. Contactors are close behind. Their contact points pit and burn from arcing, which leaves the compressor either unable to engage or unable to disengage. A related failure is the condenser fan motor, whose bearings degrade under heat and dust load. These are all straightforward repairs when caught early, and all of them can damage the compressor if left alone.
If your vents are blowing air that feels only mildly cool, the issue is more likely airflow or charge than a dead component. Watch for these signs:
A dirty or restricted coil forces the system to reject heat through a smaller surface area, which raises head pressure and shortens compressor life. Low refrigerant charge produces similar symptoms, but low charge always means a leak somewhere in the system. Simply adding refrigerant without locating the leak is a temporary fix that will fail again, usually during the next heat spike.
There is a real temptation to nurse a struggling system through the last few weeks of heat and deal with it in the fall. That calculation usually does not work in the homeowner’s favor. A capacitor replacement is a modest repair. A compressor replacement, which is what a neglected electrical fault frequently leads to, can approach the cost of a new condensing unit. Running a system that is short cycling, icing up, or drawing excess amperage also raises your utility bill every day it continues. The cheaper decision is almost always to diagnose the fault while it is still just a fault.
A proper late season diagnostic is more than a quick look. Our technicians test capacitor microfarad values against the nameplate rating, check contactor condition and amperage draw, verify refrigerant pressures and superheat, inspect the coil and blower for restriction, and confirm that the condensate drain is clear. That last item matters more in August than most homeowners expect, because monsoon humidity increases condensate volume and a plugged drain can flood a pan and trigger a safety shutoff. The point of the visit is to find the actual cause rather than to guess at it.
If your system is struggling through this heat wave, do not wait for it to stop entirely. Call Academy Plumbing, Heating, Air Conditioning and Electric to schedule a diagnostic while the repair is still small. Every job we do is backed by our 100 percent satisfaction guarantee.
Academy Plumbing, Heating, Air Conditioning and Electric, Inc.
3271 Candelaria Rd NE
Albuquerque, NM 87107
(505) 293-4949
The post The Heat Wave Continues: Late Season AC Repairs Albuquerque Homeowners Should Not Ignore appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post Beyond the AC: Summer Plumbing and Electrical Checks Every Albuquerque Home Needs appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>From July through September, your hose bibs, drip lines, and irrigation valves work harder than at any other time of year. A slow drip at an outdoor faucet or a cracked line under the gravel can run for weeks before you notice, and by then it has added up on your bill and softened the soil around your foundation. Warning signs include a faucet that will not shut off completely, unexplained wet spots in the yard, or a water bill that climbs without a change in habits. Catching and repairing these leaks early is a small job that protects both your wallet and your landscaping through the dry months.
Your water heater runs all year, but summer is the easy time to give it attention. Albuquerque’s hard water leaves mineral sediment at the bottom of the tank, where it bakes onto the heating surface, forces the unit to work harder, and slowly steals capacity and efficiency. A yearly flush clears that sediment, and a quick inspection of the anode rod and pressure relief valve catches the wear that leads to leaks and early replacement. Signs your tank is overdue include popping or rumbling sounds, water that takes longer to heat, or a rusty tint at the tap. Addressing it now is far cheaper than replacing a failed tank later.
Summer is when home electrical systems are pushed hardest. Refrigerated air, evaporative coolers, fans, and the second refrigerator in the garage can all draw at once, and an older panel was not always built for that demand. If your breakers trip on hot afternoons, your lights dim when the AC kicks on, or an outlet or panel feels warm to the touch, those are signals worth taking seriously. These are not problems to test yourself. A licensed electrician can inspect the panel, confirm it is sized and wired safely for your home’s real summer load, and correct issues before they become a fire risk.
July also brings the monsoon, and a sudden downpour finds every weakness in your home’s drainage fast. Yard drains that cannot keep up, a sump pump that has not run since last year, and low spots that channel water toward the house can all turn a storm into an indoor problem. A quick check of your drainage and sump setup before the first big storm is far easier than dealing with water where it does not belong. It is the kind of small, seasonal task that prevents the calls we get most often after the rain arrives.
Cooling matters in an Albuquerque summer, but it is only part of keeping a home comfortable and safe through the heat and the storms. A short seasonal check of your plumbing, water heater, and electrical now saves the cost and stress of an emergency later. Call Academy to get on the schedule before the busy stretch.
Academy Plumbing, Heating, A/C and Electric
3271 Candelaria Rd NE
Albuquerque, NM 87107
(505) 293-4949
The post Beyond the AC: Summer Plumbing and Electrical Checks Every Albuquerque Home Needs appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post Summer is Here – Why Annual AC Maintenance Matters More Than Ever in Albuquerque appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>A real annual maintenance visit is not a five-minute inspection. A qualified technician checks refrigerant charge against manufacturer specifications, measures temperature drop across the evaporator coil, tests capacitor health, inspects the contactor for pitting, clears the condensate drain, washes the outdoor condenser coil, tightens electrical connections, lubricates motors where applicable, and calibrates the thermostat. They check static pressure in the duct system, look at the blower wheel for dust buildup, and confirm the filter is the right size and properly seated.
Each of those checks targets a specific failure mode. A low refrigerant charge will overheat the compressor and cut years off its life. A pitted contactor causes the unit to short-cycle, which spikes electric bills and wears the motor. A clogged condensate drain backs water into the air handler and ruins drywall. Coil dust acts as insulation, forcing the system to work harder for the same output. None of these are exotic problems. They are the issues that show up year after year on units that have not been touched.
Our climate is hard on cooling equipment. Spring winds drive dust into outdoor condensers. Hard water leaves scale wherever moisture touches metal. The shift into monsoon humidity stresses systems that were sized and tuned for dry desert conditions. Long stretches of triple-digit days push compressors to the edge of their design envelope. A unit that would last fifteen to twenty years in a milder climate will struggle to hit twelve here without consistent care.
The maintenance window matters too. The right time to service a refrigerated air conditioner is spring, before the heat arrives. The right time to service or shut down a swamp cooler is fall. Trying to schedule either during a summer heat wave puts you behind a long list of emergency calls, and the small parts you might need can be on backorder. Homeowners who book service in March and April consistently spend less and avoid mid-summer downtime.
Most homeowners do not realize that nearly every major HVAC manufacturer requires documented annual maintenance to keep the warranty valid. Skip a year, and a future compressor failure that should have been covered may come out of your pocket. The warranty terms vary, but the pattern does not. Manufacturers know that consistent service is what allows their equipment to deliver the rated lifespan, and they price their warranties accordingly.
Keeping records matters. A reputable HVAC company will leave you with a written report of each visit, including refrigerant readings, electrical measurements, and any recommendations. Those reports are what manufacturers ask for when a warranty claim is filed. They are also what helps a future technician diagnose a problem quickly, because trends across multiple visits often reveal what a single snapshot cannot.
Industry data has been consistent for years. A well-maintained air conditioner uses less electricity, runs quieter, holds temperature more evenly, and lasts noticeably longer than the same unit run without service. The Department of Energy estimates that lack of maintenance can degrade efficiency by five percent per year, which compounds quickly. A unit that started life at 16 SEER2 can effectively perform like a 12 SEER2 system within a few seasons of neglect, all while the meter keeps spinning.
Then there is the breakdown question. The vast majority of mid-summer emergency calls trace back to maintenance items that would have been caught on a routine visit. Capacitors, contactors, low refrigerant, clogged drains, dirty coils, and weak fan motors. These are inexpensive parts to address in spring and expensive parts to chase in July, when stocked inventory is thinner and the home is already uncomfortable.
The most reliable households in our service area run on a simple rhythm. Spring AC tune-up, fall heating tune-up, regular filter changes between visits. They do not think about their HVAC system in August because it is doing exactly what it should. When the equipment finally does need replacement years down the line, the unit they are replacing has earned its full lifespan and then some.
If you have not had a tune-up this season, the calendar is still on your side, but the window is closing. Our team has been caring for Albuquerque HVAC systems since 1971, and we are happy to put you on a regular maintenance schedule that matches your equipment and your home. Call when you are ready to get it on the books.
Academy Plumbing, Heating, Air Conditioning and Electric, Inc. · 3271 Candelaria Road NE, Albuquerque, NM 87107 · (505) 293-4949
The post Summer is Here – Why Annual AC Maintenance Matters More Than Ever in Albuquerque appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post Common Swamp Cooler Problems Albuquerque Homeowners See Every Summer appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>This is the most common complaint of the season, and it almost always comes down to water not reaching the pads. The pump may have failed. The supply line may be kinked, clogged with mineral scale, or shut off at the saddle valve. The pads themselves may be so calcified that water no longer wicks through them. Without saturated pads, you are essentially running an attic fan that pulls in the outside temperature unchanged.
Start by checking that water is flowing into the reservoir and that the pump is humming when the cooler is on. Look at the pads. They should be uniformly wet across the full surface, not just at the top. Dry stripes mean uneven distribution, often caused by a clogged spider tube or a tilted distribution tray. If the pads are stiff, white with mineral deposits, or torn, they need to be replaced. Most homes should plan on new pads at least once a year, and homes on Albuquerque’s hard water often need them more often.
A swamp cooler that leaks is a swamp cooler with a float valve problem nine times out of ten. The float controls the water level in the reservoir, and when it sticks, fails, or sits at the wrong height, the pan overfills and water finds its way out through the overflow tube or any gap in the housing. Float valves typically need replacement every two to three years, and the small corrosion that ends their service life often happens silently.
Ceiling stains around the cooler downdraft are a more serious warning. They can indicate a leak above the unit, a failed gasket where the cooler meets the roof, or condensate making its way back into the duct. Left alone, these leaks rot drywall, damage attic insulation, and create the conditions for mold. A quick inspection at startup, and one mid-season, catches the vast majority of these problems before they become a remediation project.
Albuquerque water is famously mineral-rich, and a swamp cooler is essentially a slow-motion mineral collector. Every gallon that evaporates leaves its calcium and silica behind. Over time, that buildup coats the pump impeller, clogs the spider lines, calcifies the pads, encrusts the pan, and shortens the life of the float valve. The early signs are subtle: slightly weaker airflow, a faint musty smell, a longer time to reach a comfortable temperature in the late afternoon.
Bleed-off systems and purge pumps help by periodically draining mineral-heavy water out of the pan and refilling with fresh. Many older Albuquerque units do not have one installed. Adding a bleed-off line, descaling the pan annually, and using treated pads designed for hard water can meaningfully extend the life of your equipment. If your pump is replaced more often than your tires, mineral buildup is the likely culprit.
A swamp cooler that smells musty has standing water somewhere it should not be. The reservoir may be holding water during the off cycle, the pads may be staying damp long enough to grow mildew, or organic debris from spring and fall has settled into the pan. The fix is straightforward: drain the unit, scrub the pan with a mild cleaning solution, replace any pads that are not pristine, and check that the unit drains fully between cycles.
If the smell only appears at startup, schedule a full spring service before relying on the unit. If it persists through the season, the cooler may be the wrong size for the home, leaving the air saturated and the pads never quite drying out between cycles.
There is a point in every cooler’s life where the math changes. If you are buying a pump every other summer, replacing the float annually, and still seeing performance drop year over year, the unit has told you what it needs. Conversion to refrigerated air is worth a serious conversation, especially given how much earlier monsoon season is arriving and how much harder our cooling days have become. Even if conversion is not in the budget this year, knowing the failure points helps you keep what you have running until it is.
Catching a swamp cooler problem early is almost always cheaper than waiting. If something does not feel right, give us a call before it becomes a wet ceiling or a long July weekend without air. Our team has been keeping Albuquerque homes comfortable since 1971, and we are happy to take a look.
Academy Plumbing, Heating, Air Conditioning and Electric, Inc. · 3271 Candelaria Road NE, Albuquerque, NM 87107 · (505) 293-4949
The post Common Swamp Cooler Problems Albuquerque Homeowners See Every Summer appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post Refrigerated Air Tune-Ups Before Albuquerque’s Summer Heat Arrives appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>– A pre-season inspection finds small issues before peak heat pushes your system to its limit
– Albuquerque’s dust and dry air create specific strain that routine maintenance is built to catch
– Professional service protects efficiency, lowers cooling costs, and adds years to the equipment
There is a rhythm to comfort in the high desert. The cool mornings of May give way quickly to the steady heat of June and July, when the system you have not thought about all winter suddenly runs for hours every day. A unit that limped through last summer, or sat idle for months, may not be ready for that load. Scheduling an inspection now means a technician can find and correct a worn part, a low refrigerant charge, or a clogged filter on an ordinary spring afternoon. Wait until July, and that same small repair can become an after-hours emergency during the hottest stretch of the year, when demand for service is at its highest.
Albuquerque’s climate is hard on cooling equipment in ways that gentler regions are not. Our air is exceptionally dry and our springs are windy, which means fine dust works its way into condenser coils, air filters, and blower assemblies throughout the season. A coil coated in dust cannot release heat efficiently, so the compressor runs harder and longer to reach the temperature set on your thermostat. The city’s elevation, more than 5,000 feet above sea level, also influences how the system performs and how refrigerant behaves. A technician who works in this environment every day knows where the dust collects and what our altitude requires, and adjusts the service accordingly.
A thorough spring inspection is more than a quick look at the unit. A licensed technician checks the parts that fail quietly and the parts that fail expensively. A typical visit covers:
– Refrigerant levels and a check for leaks along the lines
– Cleaning the condenser and evaporator coils so they can shed heat
– Inspecting electrical connections, the capacitor, and the contactor for wear
– Testing the thermostat and confirming it reads accurately
– Clearing the condensate drain to prevent water backup and moisture damage
– Measuring airflow and replacing or recommending a fresh filter
Each of these steps either restores efficiency or heads off a breakdown later in the season. Together they keep the system running closer to the performance it had when it was new, which shows up directly in your summer energy bills.
You do not have to wait for a full failure to know something is wrong. Pay attention if your home takes longer than usual to cool, if certain rooms stay warm while others feel comfortable, or if your energy bills climbed last summer without an obvious reason. Unusual sounds when the unit starts, a musty smell from the vents, and short cycling, where the system turns on and off in rapid bursts, all deserve a professional’s attention. None of these signs guarantees the worst, but each is easier and less disruptive to resolve in spring than in the middle of a July afternoon.
Cooling equipment rewards the homeowner who plans ahead. A professional inspection now is a straightforward way to enter summer with confidence, knowing your refrigerated air system is ready for the heat Albuquerque reliably delivers. Call Academy to schedule your pre-season check while the calendar still works in your favor.
3271 Candelaria Rd NE
Albuquerque, NM 87107
(505) 293-4949
The post Refrigerated Air Tune-Ups Before Albuquerque’s Summer Heat Arrives appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post No Fooling: It’s Already Time to Schedule Your Spring Cooler Changeover appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>Albuquerque’s high desert climate makes evaporative coolers an ideal cooling solution for most of the year. The city’s average relative humidity sits around 44%, and annual rainfall averages only about nine inches, creating the dry conditions these systems need to work effectively. But that same dry climate, combined with our hard water and persistent spring winds, means your cooler needs professional attention before you flip the switch for the season.
By late April, daily highs regularly reach the mid-70s. By May, those numbers push into the low 80s. Once June arrives, temperatures routinely hit the 90s, and every HVAC company in the metro area is booked solid. Homeowners who wait until they actually need cooling often find themselves sweating through a two-week wait for service. Scheduling in early April means you choose your appointment time rather than taking whatever is available.
Starting up your evaporative cooler is more than reconnecting the water line and flipping a breaker. A proper spring dewinterization involves a systematic inspection and service of every component that sat dormant through the winter months.
A qualified technician will remove the winter cover and inspect the exterior housing for rust, corrosion, or damage from Albuquerque’s notorious spring winds. Inside, the reservoir, float valve, water distribution lines, and pump screen all need thorough cleaning. Winter dormancy allows mineral deposits from our hard water to crystallize on surfaces, and desert dust settles into every opening regardless of how well the unit was covered.
Cooling pads are the heart of any evaporative system. Pads that survived last summer may have degraded over winter, becoming brittle, compressed, or harboring musty odors. Fresh pads restore full water absorption and airflow, which directly translates to better cooling performance and cleaner indoor air. Standard cooler pads should be replaced annually, while Mastercool or Aerocool pads typically last three to five years depending on water hardness.
Water lines require careful inspection for cracks caused by winter freezing. Even a minor water line leak can damage your roof, exterior walls, or ceilings. The motor, belt, and bearings also need evaluation. A worn belt can slip or snap on the hottest day of the year, and dry bearings lead to noisy operation and premature motor failure.
Putting off your cooler startup feels like saving money until something goes wrong. The most common issues Academy Plumbing sees from neglected coolers follow a predictable pattern. Clogged or deteriorated pads force the system to work harder while delivering weak, sometimes musty-smelling airflow. Mineral scale restricts water flow to the pads, creating dry spots that reduce cooling capacity significantly. Corroded pump screens reduce water circulation, and cracked water lines leak silently until the damage becomes visible inside the home.
A routine spring startup service costs a fraction of what an emergency repair runs during peak summer, and that does not account for the discomfort of waiting for service when every technician in town is already booked. Regular maintenance also extends the overall lifespan of your evaporative cooler, protecting your investment year after year.
Academy Plumbing’s experienced technicians handle every type of evaporative cooler in the Albuquerque area, from standard rooftop units to high-efficiency ground-level systems. Our spring startup service includes a complete inspection, cleaning, pad evaluation, water line check, and system test so you know your cooler is ready before you need it.
Do not wait for the first hot week to find out your cooler is not working. Call Academy Plumbing today to schedule your spring changeover and get ahead of the summer rush.
Academy Plumbing, Heating, Air Conditioning and Electric
3271 Candelaria Rd NE
Albuquerque, NM 87107
(505) 293-4949
academyplumbing.net
The post No Fooling: It’s Already Time to Schedule Your Spring Cooler Changeover appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>The post Tankless Water Heaters Aren’t Right for Every Home. Here’s How to Know If Yours Qualifies appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>Traditional tank water heaters store 40 to 80 gallons of hot water, maintaining temperature through continuous heating cycles. Tankless units eliminate storage entirely. They heat water on demand as it flows through the unit, using high-powered burners or electric elements to raise temperature instantly. This fundamental difference creates both advantages and limitations. Understanding these trade-offs determines whether tankless makes sense for your household.
When conditions are right, tankless water heaters deliver measurable benefits.
Unlimited hot water supply: Tank systems eventually deplete stored hot water. Run the dishwasher, washing machine, and shower simultaneously, and someone’s getting a cold surprise. Tankless units heat continuously as long as water flows, eliminating the concept of “running out.”
Energy efficiency: Tank heaters maintain temperature 24/7, even when you’re not using hot water. This standby heat loss accounts for 10 to 20 percent of your water heating costs. Tankless units only operate when you open a hot water tap, eliminating standby losses entirely.
Space savings: A tank water heater occupies 16 to 20 square feet of floor space. Tankless units mount on walls, typically measuring 28 inches tall, 20 inches wide, and 10 inches deep. For homes with limited mechanical room space, this difference matters.
Longevity: Quality tankless systems last 20 to 25 years with proper maintenance. Tank heaters typically require replacement after 10 to 15 years.
These advantages sound compelling. But they only materialize if your home meets specific criteria.
Insufficient gas supply: Gas-fired tankless units require substantial fuel input to heat water instantly. A typical residential tankless heater needs 150,000 to 200,000 BTU per hour. Your existing gas line, originally sized for a 40,000 BTU tank heater, cannot supply this demand.
Upgrading gas supply means running larger diameter pipe from your meter to the water heater location. In some cases, it means upgrading the meter itself. This infrastructure work represents significant additional expense beyond the unit itself. If your gas meter sits 100 feet from your desired heater location, the upgrade becomes impractical.
Electrical limitations: Electric tankless heaters draw enormous current. A whole-house electric tankless unit requires 100 to 150 amps at 240 volts. Most homes have 200-amp service total. Installing electric tankless often means electrical panel upgrades, dedicated circuits, and potentially service upgrades from your utility company.
The electrical work alone represents a substantial investment. For many homes, electric tankless simply isn’t feasible without comprehensive electrical system upgrades.
Simultaneous high-demand usage: Tankless units heat water at a specific flow rate. A quality residential unit might deliver 8 gallons per minute at a 70-degree temperature rise (roughly what you need in Albuquerque to heat 55-degree groundwater to 125-degree shower temperature).
Eight gallons per minute sounds generous. But consider this scenario: your teenager showers (2.5 gpm), someone starts the dishwasher (1.5 gpm), and the washing machine fills (3 gpm). You’ve just exceeded your tankless unit’s capacity. Water temperature drops, or flow decreases.
Larger families with overlapping usage patterns often need multiple tankless units or strategically placed point-of-use heaters. This eliminates the efficiency advantage entirely.
Hard water without treatment: Albuquerque’s hard water creates scale buildup inside tankless heat exchangers. The narrow passages that enable instant heating also trap mineral deposits. Without water softening, tankless units require descaling maintenance every 6 to 12 months. Skip this maintenance and your unit fails prematurely.
A whole-home water softener becomes a necessary companion investment when installing tankless in our region.
Certain home profiles align perfectly with tankless advantages.
Smaller households with sequential usage: One or two people rarely use multiple hot water sources simultaneously. Your 8 gpm tankless unit never approaches capacity limits. You experience genuinely unlimited hot water without the simultaneous demand challenges larger families face.
Homes with existing adequate gas infrastructure: If your home already has commercial-grade gas service or recently upgraded gas lines, installation becomes far more practical. You avoid the major infrastructure expense that makes tankless impractical for many residential applications.
New construction or major renovation: When you’re already running new gas lines, installing electrical panels, and opening walls, adding tankless-compatible infrastructure costs incrementally less. The timing aligns with construction needs rather than requiring dedicated retrofitting.
Secondary or vacation homes: Tankless units don’t maintain temperature when unused, making them ideal for properties occupied intermittently. You eliminate standby losses during weeks or months of vacancy.
Homes with water treatment systems: If you’ve already installed whole-home water softening or filtration, you’ve addressed tankless units’ primary maintenance concern. Your investment protects the tankless system while serving broader water quality goals.
Before evaluating tankless suitability, understand your household’s actual hot water usage patterns. How many people live in your home? Do family members shower sequentially or simultaneously? Do you run appliances during morning routines?
Peak demand times reveal whether tankless capacity matches your needs. A family of five preparing for school and work between 6:00 and 8:00 AM creates different demands than a retired couple with flexible schedules.
Your home’s existing infrastructure matters equally. Gas line sizing, electrical panel capacity, and available installation locations all factor into feasibility and total investment required.
The tankless decision requires honest assessment of your specific situation. Usage patterns, existing infrastructure, budget, and household size all factor into whether tankless delivers actual benefits or just creates expensive complications.
We’ve installed hundreds of water heaters throughout Albuquerque since 1999. We evaluate your home’s infrastructure, calculate your hot water demand, assess your budget parameters, and recommend solutions that actually work for your situation.
Sometimes that’s tankless. Often it’s not. Our job is accurate assessment, not product pushing.
Call us at (505) 821-2922 or visit academyplumbingnm.com. We’ll evaluate your home’s candidacy for tankless technology and explain your options clearly.
When tankless is right, it’s incredible. When it’s wrong, it’s frustrating and expensive. Let’s determine which category your home falls into before you invest.
Your hot water system should match your household’s actual needs, not marketing promises. We’ll help you figure out what that means for your specific situation.
The post Tankless Water Heaters Aren’t Right for Every Home. Here’s How to Know If Yours Qualifies appeared first on Academy Plumbing, Heating and Air Conditioning, Electric.
]]>