Comments for 3D Printing: How-to

Comment on Leveling a 3D Printer Bed: Step-by-Step by Building the Creality Ender 3 Pro: Tips and Tricks - 3D Printing: How-to

Building the Creality Ender 3 Pro: Tips and Tricks - 3D Printing: How-to — Thu, 30 Mar 2023 23:29:16 +0000

[…] Leveling a 3D Printer Bed: Step-by-Step […]

Comment on Calibrating and Leveling My 3D Printer by Leveling a 3D Printer Bed: Step-by-Step - 3D Printing: How-to

Leveling a 3D Printer Bed: Step-by-Step - 3D Printing: How-to — Thu, 30 Mar 2023 23:26:51 +0000

[…] I learned many years back (see Calibrating and Leveling My 3D Printer), one of the most important (and often frustrating) steps in setting up your 3D printer is leveling […]

Comment on Calibrating and Leveling My 3D Printer by Building the Creality Ender 3 Pro: Tips and Tricks - 3D Printing: How-to

Building the Creality Ender 3 Pro: Tips and Tricks - 3D Printing: How-to — Thu, 30 Mar 2023 21:47:42 +0000

[…] Finally, it is time to turn you printer on and set it up for printing. The first thing you will need to do is level the bed. This step is very critical; If your bed is too low your prints won’t stick to the bed. If your bed is too high, the nozzle can scrape on the bed and damage it. If it is not level you can have both of the above issues on a single print. For help leveling your printer you can go to my article: Calibrating and Leveling My 3D Printer […]

Comment on Extruder Head Upgrade – Second attempt by Anti-Sag Truss - 3D Printing How-to

Anti-Sag Truss - 3D Printing How-to — Tue, 07 Jun 2016 06:09:58 +0000

[…] GT2 belt arrived a few days ago, but I wanted to successfully upgrade my Extruder Head before moving on to something else. This time I am planning to install Proto-Plastik’s […]

Comment on X-Gantry Small Parts by X-Gantry Assembly - 3D Printing How-to

X-Gantry Assembly - 3D Printing How-to — Sun, 05 Jun 2016 12:31:50 +0000

[…] is part 3 of my X-Gantry Upgrade, for the previous article follow this link. Yesterday I printed the smaller parts needed for the gantry, and today I plan to complete the […]

Comment on X-Gantry Assembly by X-Gantry Small Parts - 3D Printing How-to

X-Gantry Small Parts - 3D Printing How-to — Sun, 05 Jun 2016 12:29:42 +0000

[…] I’ll work on reshaping the spacers tomorrow while i finish printing the parts for the gantry. Time for bed… Follow this link for the conclusion. […]

Comment on X-Gantry Small Parts by X-Gantry Upgrade - 3D Printing How-to

X-Gantry Upgrade - 3D Printing How-to — Sun, 05 Jun 2016 12:27:34 +0000

[…] This is obviously going to take a few more nights… X-Gantry Upgrade Part 2 […]

Comment on Extruder Head Upgrade – Second attempt by Extruder Head Upgrade - 3D Printing How-to

Extruder Head Upgrade - 3D Printing How-to — Sun, 05 Jun 2016 12:23:37 +0000

[…] To see my working upgrade follow this link. […]

Comment on Extruder Head Upgrade by Extruder Head Upgrade - Second attempt - 3D Printing How-to

Extruder Head Upgrade - Second attempt - 3D Printing How-to — Sun, 05 Jun 2016 01:56:01 +0000

[…] I am going to upgrade my extruder head… again. My last attempt looked great, but was a prime example of why you should research a little more before you print a […]

Comment on X-Gantry Upgrade by X-Gantry Assembly - 3D Printing How-to

X-Gantry Assembly - 3D Printing How-to — Wed, 25 May 2016 08:13:26 +0000

[…] is part 3 of my X-Gantry Upgrade. Yesterday I printed the smaller parts needed for the gantry, and today I plan to complete the […]